ES-7N black
NEW EPOS MODEL ES-7N
The second model out of three.
Impedance: 4 Ohm, minimum 3 Ohm at 15kHz
Sensitivity: 2.83V, 1m: 86dB/89dB
Woofer: 130mm PP cone woofer
Tweeter: 28mm ceramic coated Aluminum dome
Crossover Frequency: 2.000 Hz
Dimensions: 290 x 200 x 270 mm (HWD)
Stand: recommended height around 700 mm
Weight: 7,6 kg
Finish: Orange semi matte, Walnut, White semi matte, Black semi matte
Up to 12 interest free installments with Credit Card
Shipping Options
„Two-way reflex loaded bookshelf speaker.“
Many customers asked for a smaller speaker, so the development group created a smaller baby EPOS. This speaker should be a real bookshelf with a size small enough to go into typical IKEA designs for example. But how to make it?
Smaller speakers are especially giving the designer some severe headaches. This has something to do with the size of the front baffle and the small baffle’s influence on a speaker’s response curve. A design for free space should be different from one that plays close to a wall or inside a bookshelf.
In order to work in a semi-free space (some distance from a wall) and on a wall, the crossover filter can be changed with a switch on the backside of the speaker.
Now, you are free to choose the place of your speakers without making compromises in tonal balance.
The cabinet uses 2x8mm MDF panels with a high-loss damping layer in between to control unwanted resonances of the box itself. An additional wooden block on the top helps to optimize the Stereo image. Only a single brace was necessary to make the cabinet quiet. Four inserts on the bottom take 4mm screws, and the speaker comes delivered with silicon rubber spikes for good isolation between the speaker and the ground.
The stand for EPOS ES-7N should be around 70cm high.
The crossover features a switch to choose between two versions of tonal balance.
With the switch in the top position, the best placement is at some distance from a wall between 30cm and 50cm.
In the bottom position, the speaker should play close to a wall or inside a bookshelf. Please try both positions to find the best result in your room.
The response curve has been tailored to use the speaker in semi-free air or very near a wall.
The bottom-end roll-off is flat to deal with the room/wall gain at low frequencies and to avoid booming bass. The speaker’s sensitivity is around 86dB for Position up and 89dB for Position down of the switch.
In the same category
Silver 200 7G Ash
Silver 200 7G
In creating the Monitor Audio Silver 200 7G speakers, we made lots of small technical decisions – such as enhancing our Rigid Surface Technology (RST) II and coming up with a new crossover system. But all of these complex moves were done with a simple aim in mind. Great, lifelike audio, across all types of music and for all our customers. A choice of real-wood veneers – including new Natural Walnut and Ash options – enables you to integrate your speakers perfectly with the rest of your home, while even the smallest touches make a difference, like the new moulded feet designed specifically for modern hardwood floors and carpets. You might not notice every feature right away, but you can rest assured we’ve carefully considered them all.
EL50
EL50 ANNIVERSARY
ATC is delighted to introduce the EL50 Anniversary to audiophiles and music lovers seeking long-lasting high performance, design and engineering quality. It is the latest evolution of the legendary ATC 50 loudspeaker design, featuring ATCs discrete active tri-amp technology, renowned drive units and a new elliptical curved cabinet for optimal radiation from the mid and high-frequency drive units. Its industrial design draws from the EL150, released in 2006, the first ATC loudspeaker to employ an elliptical enclosure and designed by Billy Woodman. Leather detailing on the front face and beautiful hand-selected veneers further elevate the design.
Silver 50 7G Ash
Silver 50 7G
Designed to give you the deep, rich bass extension usually only found in a larger floorstander, the Silver 50 7G bookshelf speakers are an excellent choice when space is at a premium. It’s engineered for the kind of real-world spaces we live in, which means we’ve optimised the bass for scenarios like being placed close to a wall. With a choice of real-wood veneers, and from Satin White to High Gloss Black, you’ll find the perfect look to fit your home. And most importantly of all, thanks to the new Rigid Surface Technology (RST) II mid-bass driver design, you’ll enjoy pin sharp clarity in every track.
ES-14N black
BACK TO THE FUTURE.
A classic speaker returns to the future.
Frequency Response: 40Hz – 23kHz (-6dB) 33Hz – 25kHz (-10dB)
Average Impedance: > 6 Ohm
Minimum Impedance: 4.3 Ohm @ 160Hz
Sensitivity: 87dB @oe2.823V / 1m
Distortion: 0.2% THD @ 1W
Crossover Frequency: 2700 Hz
Bass Unit: High Power 7“, 35 mm voice coil diameter, Hybrid Ferrite and Neodymium magnet, injection molded cone with variable thickness and Mica filling. Low hysteresis rubber surround.
HF Unit: 28 mm tweeter with Aluminum/Ceramic compound dome and no Ferrofluid
Dimensions: 491 x 250 x 385 mm (HWD)
Stand: recommended height 515 mm
Weight: 16 kg without stand
Finish: Walnut, White semi matte, Black semi matte
SCM7 v3 Satin Black
SCM7
Overview
New ATC designed and built 25mm soft dome HF unit with precision alloy wave guide.
125mm ATC mid-bass unit with integral soft dome.
In-house, hand-wound ribbon wire mid-bass voicecoil.
Massive optimised mid-bass motor assembly.
Flat impedance curve allowing easy load for amplifiers.
Veneered Finish Options – Cherry, Black Ash.
Painted Finish Options – Satin Black, Satin White.
6 year warranty.
“…you will be amazed at its rhythmic and dynamic alacrity.” Hi-Fi Choice, May 2014. Group test winner!
Elegance DB9-D
Elegance Diamond edition
Imagine you have the looks of your favorite Elegance loudspeaker, but with the refinement of a Diamond tweeter. It is now possible with the Elegance Diamond edition. The signature Elegance True Beryllium tweeter is exchanged with a 25m Diamond tweeter, along with the inside cabling and trimming details on the outside, creating a new refined look to the Elegance Collection.
Silver 50 7G High Gloss Black
Silver 50 7G
Designed to give you the deep, rich bass extension usually only found in a larger floorstander, the Silver 50 7G bookshelf speakers are an excellent choice when space is at a premium. It’s engineered for the kind of real-world spaces we live in, which means we’ve optimised the bass for scenarios like being placed close to a wall. With a choice of real-wood veneers, and from Satin White to High Gloss Black, you’ll find the perfect look to fit your home. And most importantly of all, thanks to the new Rigid Surface Technology (RST) II mid-bass driver design, you’ll enjoy pin sharp clarity in every track.
Silver 300 7G High Gloss Black
Silver 300 7G
The Silver 300 7G speakers incorporate some of our most advanced engineering yet, for sound that will leave you speechless. Much of the technology at play is hidden, but there’s still plenty to feast your eyes on. New grilles, driver trims and feet give an even more refined look, only accentuated by five different choices of wood veneer, including Natural Walnut, Ash, Black Oak, Satin White and High Gloss Black.
The Silver 300 7G features real-wood veneers for a natural look, along with a newly developed Rigid Surface Technology (RST) II driver design for the most natural possible sound. It’s designed to reduce distortion, so when your music’s loud, it remains very, very clear.
ES-7N walnut
NEW EPOS MODEL ES-7N
The second model out of three.
Impedance: 4 Ohm, minimum 3 Ohm at 15kHz
Sensitivity: 2.83V, 1m: 86dB/89dB
Woofer: 130mm PP cone woofer
Tweeter: 28mm ceramic coated Aluminum dome
Crossover Frequency: 2.000 Hz
Dimensions: 290 x 200 x 270 mm (HWD)
Stand: recommended height around 700 mm
Weight: 7,6 kg
Finish: Orange semi matte, Walnut, White semi matte, Black semi matte
SCM40 Satin White
SCM40
Overview
New ATC designed and built 25mm soft dome HF unit with precision alloy wave guide.
ATC 164mm bass driver.
Massive optimised motor assembly.
ATC Soft Dome mid-range driver.
Flat impedance curve allowing easy load for amplifiers.
Veneered Finish Options – Cherry, Black Ash.
Painted Finish Options – Satin Black, Satin White.
6 year warranty.
“Given a serious source and recording the new ATC SCM40 is superb – I know of no price rivals that give this level of accuracy, speed and insight…it’s capable of a level of transparency you normally only expect from loudspeakers at three or four times its price.” Hi-Fi Choice, October 2014
ES-28N
„All good things go by three“ is a proverb we often use in Germany if something happens the third time. The new ES-28N is the third model in the current EPOS line-up, and on top of it, it’s a 3-way loudspeaker made by a designer who is well known for doing 2-way systems even with bigger woofers. So what did change his mind*?
(*answered in Description)
SCM7 v3 Satin White
SCM7
Overview
New ATC designed and built 25mm soft dome HF unit with precision alloy wave guide.
125mm ATC mid-bass unit with integral soft dome.
In-house, hand-wound ribbon wire mid-bass voicecoil.
Massive optimised mid-bass motor assembly.
Flat impedance curve allowing easy load for amplifiers.
Veneered Finish Options – Cherry, Black Ash.
Painted Finish Options – Satin Black, Satin White.
6 year warranty.
“…you will be amazed at its rhythmic and dynamic alacrity.” Hi-Fi Choice, May 2014. Group test winner!
Yvette
Yvette**
For me, the organic design of the Yvette makes it the Wilson product that comes closest to the magic of an Apple design—and the one most pleasing to my eye. That beauty in the eye of this beholder, combined with its rich tonal palette, its facility to re-create a large lifelike soundstage and its flair for sounding larger than it is, make the Yvette my new reference—a speaker that fits my space and fulfills my requirements for engaging, dynamic, rich sound...
Dennis Davis , The Audio Beat
**PLEASE CALL FOR PRICE
Viewed products
Meze STRADA
STRADA
Meet the STRADA - a pair of closed-back dynamic headphones crafted for tonal balance and musical intimacy. With its full-bodied sound, excellent noise isolation, and natural sense of space, it delivers a harmonious acoustic experience where detail, texture, and dynamics come through with effortless precision.
ES-7N white
NEW EPOS MODEL ES-7N
The second model out of three.
Impedance: 4 Ohm, minimum 3 Ohm at 15kHz
Sensitivity: 2.83V, 1m: 86dB/89dB
Woofer: 130mm PP cone woofer
Tweeter: 28mm ceramic coated Aluminum dome
Crossover Frequency: 2.000 Hz
Dimensions: 290 x 200 x 270 mm (HWD)
Stand: recommended height around 700 mm
Weight: 7,6 kg
Finish: Orange semi matte, Walnut, White semi matte, Black semi matte
Sasha DAW
Sasha DAW**
I designed the WATT for my own use, so I was surprised at people’s excitement to buy it. This was the first time I truly understood Authentic Excellence. I designed the loudspeaker I wanted and was delighted when others wanted it too.
David A. Wilson , 1944-2018
**PLEASE CALL FOR PRICE
Acoustic Diode
Acoustic Diode**
The new Wilson Acoustic Diode isn’t an optional device; it’s an essential one. It dramatically lowers the noise floor, both boosting dynamics and revealing previously obscured musical details.
Jacob Heilbrunn
**PLEASE CALL FOR PRICE
SCM20ASL
SCM20ASL | ACTIVE
The active SCM20ASL features an on-board 250W Amp Pack. Simply pair with a suitable pre-amplifier, DAC/pre or streaming-pre-amp for stunning results.
The active SCM20ASL replaces the passive crossover and the driving amplifier of a 'conventional' system with a precisely matched 'Amp Pack', mounted to the rear of the loudspeaker cabinet. The electronic system consists of a balanced input feeding a 2nd order active electronic crossover which, in turn, feeds a pair of class A/B power amplifiers, carefully tailored to the exact requirements of the mid/bass and high-frequency drive units.
OB-4 black
OB–4
OB–4 is our portable high-fidelity bluetooth loudspeaker featuring a 40 hour rechargeable battery. listen using line input, bluetooth, FM radio or disk mode. OB–4 memorizes everything you play on an endless looping tape, so you can rewind the radio and remix anything, all in OB–4. features a folding handle that doubles as a stand and extended antenna.
Bluetooth, FM–signal, line-in and disk mode
72 hrs radio listening on a single charge or 40 hours of listening via bluetooth
uv resistant paint
compatible with ortho remote and orthoplay app
dimensions: 232.5 x 284 x 57.5 mm | 9.2 x 11.2 x 2.3 in
NEW EPOS MODEL ES-7N
The second model out of three.
Impedance: 4 Ohm, minimum 3 Ohm at 15kHz
Sensitivity: 2.83V, 1m: 86dB/89dB
Woofer: 130mm PP cone woofer
Tweeter: 28mm ceramic coated Aluminum dome
Crossover Frequency: 2.000 Hz
Dimensions: 290 x 200 x 270 mm (HWD)
Stand: recommended height around 700 mm
Weight: 7,6 kg
Finish: Orange semi matte, Walnut, White semi matte, Black semi matte